Project

General

Profile

Actions

OpenBSD on beaglebone black

1. 概略

beaglebone blackについてはこちら 。こいつでOpenBSD が動きます。最新の情報についてはこちら をどうぞ。

2. 注意すべきこと

この記事を書いている現状では、HDMIを経由した画面出力はありません。つまり、シリアルコンソールかnetwork経由でしか弄れません。
それでも、画面出力デバイスがそもそも全くないIO-DATAのUSL-5Pのようなケース(USBデバイスサーバ、という名前で売り出しているのである意味当然ではあります。ちなみにこちらはOpenBSD/landisk で稼働)よりはマシでしょうけれど、ね。

ちなみにシリアルコンソールのpin配置は以下の通り;

  • pin1: GND
  • pin4: RxD
  • pin5: TxD

Debian GNU/Linuxの場合のシリアルコンソール用login accountは次の通り;

  • login root
  • password: (なし)

なおOpenBSDの場合、installプロセスでパスワードの設定を要求されますので、省略はできません。

3. install log

他で色々と参考になりそうなので、貼り付けておきます。

U-Boot SPL 2014.04-00015-gb4422bd (Apr 22 2014 - 13:24:29)
reading args
spl_load_image_fat_os: error reading image args, err - -1
reading u-boot.img
reading u-boot.img

U-Boot 2014.04-00015-gb4422bd (Apr 22 2014 - 13:24:29)

I2C:   ready
DRAM:  512 MiB
NAND:  0 MiB
MMC:   OMAP SD/MMC: 0, OMAP SD/MMC: 1
*** Warning - readenv() failed, using default environment

Net:   <ethaddr> not set. Validating first E-fuse MAC
cpsw, usb_ether
Hit any key to stop autoboot:  0 
gpio: pin 53 (gpio 53) value is 1
mmc0 is current device
gpio: pin 54 (gpio 54) value is 1
SD/MMC found on device 0
reading uEnv.txt
159 bytes read in 10 ms (14.6 KiB/s)
gpio: pin 55 (gpio 55) value is 1
Loaded environment from uEnv.txt
Importing environment from mmc ...
Checking if uenvcmd is set ...
gpio: pin 56 (gpio 56) value is 1
Running uenvcmd ...
reading bsd.umg
7163548 bytes read in 412 ms (16.6 MiB/s)
## Booting kernel from Legacy Image at 82800000 ...
   Image Name:   boot
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    7163484 Bytes = 6.8 MiB
   Load Address: 80300000
   Entry Point:  80300000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK

Starting kernel ...

OpenBSD/omap booting ...
arg0 0x0 arg1 0xe05 arg2 0x80000100
atag core flags 0 pagesize 0 rootdev 0
atag cmdline [sd0i:/bsd.umg]
atag mem start 0x80000000 size 0x20000000
bootfile: sd0i:/bsd.umg
bootargs: 
memory size derived from u-boot
bootconf.mem[0].address = 80000000 pages 131072/0x20000000
Allocating page tables
freestart = 0x809d5000, free_pages = 128555 (0x0001f62b)
IRQ stack: p0x80a03000 v0xc0a03000
ABT stack: p0x80a04000 v0xc0a04000
UND stack: p0x80a05000 v0xc0a05000
SVC stack: p0x80a06000 v0xc0a06000
Creating L1 page table at 0x809d8000
Mapping kernel
Constructing L2 page tables
undefined page pmap board type: beaglebone
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.
Copyright (c) 1995-2015 OpenBSD. All rights reserved.  http://www.OpenBSD.org

OpenBSD 5.7-beta (RAMDISK-OMAP) #1: Fri Jan  9 20:02:48 AEDT 2015
    jsg@armv7.jsg.id.au:/usr/src/sys/arch/armv7/compile/RAMDISK-OMAP
real mem  = 536870912 (512MB)
avail mem = 515444736 (491MB)
mainbus0 at root
cpu0 at mainbus0: ARM Cortex A8 R3 rev 2 (ARMv7 core)
cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled
cpu0: 32KB(64b/l,4way) I-cache, 32KB(64b/l,4way) wr-back D-cache
omap0 at mainbus0: BeagleBone
prcm0 at omap0 rev 0.2
sitaracm0 at omap0: control module, rev 1.0
intc0 at omap0 rev 5.0
omap0: device edma unit 0 not configured
dmtimer0 at omap0 rev 3.1
dmtimer1 at omap0 rev 3.1
omdog0 at omap0 rev 0.1
omgpio0 at omap0: rev 0.1
omgpio1 at omap0: rev 0.1
omgpio2 at omap0: rev 0.1
omgpio3 at omap0: rev 0.1
omap0: device tiiic unit 0 not configured
omap0: device tiiic unit 1 not configured
omap0: device tiiic unit 2 not configured
ommmc0 at omap0
sdmmc0 at ommmc0
ommmc1 at omap0
sdmmc1 at ommmc1
com0 at omap0: ti16750, 64 byte fifo
com0: console
cpsw0 at omap0: version 1.12 (0), address d0:5f:b8:f5:94:f9
ukphy0 at cpsw0 phy 0: Generic IEEE 802.3u media interface, rev. 1: OUI 0x0001f0, model 0x000f
scsibus0 at sdmmc0: 2 targets, initiator 0
sd0 at scsibus0 targ 1 lun 0: <SD/MMC, Drive #01, > SCSI2 0/direct fixed
sd0: 7580MB, 512 bytes/sector, 15523840 sectors
scsibus1 at sdmmc1: 2 targets, initiator 0
sd1 at scsibus1 targ 1 lun 0: <SD/MMC, Drive #01, > SCSI2 0/direct fixed
sd1: 3688MB, 512 bytes/sector, 7553024 sectors
boot device: sd0
root on rd0a swap on rd0b dump on rd0b
WARNING: CHECK AND RESET THE DATE!
erase ^?, werase ^W, kill ^U, intr ^C, status ^T

Welcome to the OpenBSD/armv7 5.7 installation program.
(I)nstall, (U)pgrade, (A)utoinstall or (S)hell? i
At any prompt except password prompts you can escape to a shell by
typing '!'. Default answers are shown in []'s and are selected by
pressing RETURN.  You can exit this program at any time by pressing
Control-C, but this can leave your system in an inconsistent state.

Terminal type? [vt220] 
System hostname? (short form, e.g. 'foo') foo

Available network interfaces are: cpsw0.
Which network interface do you wish to configure? (or 'done') [cpsw0] 
IPv4 address for cpsw0? (or 'dhcp' or 'none') [dhcp] 
DHCPDISCOVER on cpsw0 - interval 1
DHCPDISCOVER on cpsw0 - interval 2
DHCPOFFER from xx.xx.xx.xx (00:17:e0:a1:61:84)
DHCPREQUEST on cpsw0 to 255.255.255.255
DHCPACK from xx.xx.xx.xx (00:17:e0:a1:61:84)
bound to xx.xx.xx.xx -- renewal in 43200 seconds.
IPv6 address for cpsw0? (or 'rtsol' or 'none') [none] rtsol
Available network interfaces are: cpsw0.
Which network interface do you wish to configure? (or 'done') [done] 
Using DNS domainname tknd.jp
Using DNS nameservers at xx.xx.xx.xx xx.xx.xx.xx

Password for root account? (will not echo) 
Password for root account? (again) 
The root password must be set.
Password for root account? (will not echo) 
Password for root account? (again) 
Start sshd(8) by default? [yes] 
Start ntpd(8) by default? [no] 
Setup a user? (enter a lower-case loginname, or 'no') [no] 
What timezone are you in? ('?' for list) [Japan] 

Available disks are: sd0 sd1.
Which disk is the root disk? ('?' for details) [sd0] ?
sd0: Drive #01 (7.4G)
sd1: Drive #01 (3.6G)
Available disks are: sd0 sd1.
Which disk is the root disk? ('?' for details) [sd0] 
Use DUIDs rather than device names in fstab? [yes] 
Disk: sd0       geometry: 966/255/63 [15523840 Sectors]
Offset: 0       Signature: 0xAA55
            Starting         Ending         LBA Info:
 #: id      C   H   S -      C   H   S [       start:        size ]
-------------------------------------------------------------------------------
*0: 0C      0   1   1 -      1 254  63 [          63:       32067 ] Win95 FAT32L
 1: 00      0   0   0 -      0   0   0 [           0:           0 ] unused      
 2: 00      0   0   0 -      0   0   0 [           0:           0 ] unused      
 3: A6      0   1   2 -      1 254  63 [          64:       32066 ] OpenBSD     
Use (W)hole disk or (E)dit the MBR? [whole] W
Creating a msdos partition and an OpenBSD partition for rest of sd0...done.
/dev/rsd0i: 32668 sectors in 8167 FAT16 clusters (2048 bytes/cluster)
bps=512 spc=4 res=1 nft=2 rde=512 sec=32768 mid=0xf8 spf=32 spt=63 hds=255 hid=64
The auto-allocated layout for sd0 is:
#                size           offset  fstype [fsize bsize  cpg]
  a:            99.8M            32832  4.2BSD   2048 16384    1 # /
  b:           119.6M           237216    swap                   
  c:          7580.0M                0  unused                   
  d:           151.7M           482176  4.2BSD   2048 16384    1 # /tmp
  e:           131.5M           792768  4.2BSD   2048 16384    1 # /var
  f:           919.8M          1062016  4.2BSD   2048 16384    1 # /usr
  g:           523.9M          2945760  4.2BSD   2048 16384    1 # /usr/X11R6
  h:          2087.6M          4018656  4.2BSD   2048 16384    1 # /usr/local
  i:            16.0M               64   MSDOS                   
  j:          1031.9M          8294048  4.2BSD   2048 16384    1 # /usr/src
  k:          1315.8M         10407392  4.2BSD   2048 16384    1 # /usr/obj
  l:          1182.4M         13102208  4.2BSD   2048 16384    1 # /home
Use (A)uto layout, (E)dit auto layout, or create (C)ustom layout? [a] C

You will now create an OpenBSD disklabel inside the OpenBSD MBR
partition. The disklabel defines how OpenBSD splits up the MBR partition
into OpenBSD partitions in which filesystems and swap space are created.
You must provide each filesystem's mountpoint in this program.

The offsets used in the disklabel are ABSOLUTE, i.e. relative to the
start of the disk, NOT the start of the OpenBSD MBR partition.

Label editor (enter '?' for help at any prompt)
> a
partition: [a] 
offset: [32832] 
size: [15491008] 7062M
Rounding size to cylinder (16065 sectors): 14473863
FS type: [4.2BSD] 
mount point: [none] /
Rounding size to bsize (32 sectors): 14473856
> p
OpenBSD area: 32832-15523840; size: 15491008; free: 1017152
#                size           offset  fstype [fsize bsize  cpg]
  a:         14473856            32832  4.2BSD   2048 16384    1 # /
  c:         15523840                0  unused                   
  i:            32768               64   MSDOS                   
> a
partition: [b] 
offset: [14506688] 
size: [1017152] 
FS type: [swap] 
> p
OpenBSD area: 32832-15523840; size: 15491008; free: 0
#                size           offset  fstype [fsize bsize  cpg]
  a:         14473856            32832  4.2BSD   2048 16384    1 # /
  b:          1017152         14506688    swap                   
  c:         15523840                0  unused                   
  i:            32768               64   MSDOS                   
> ?
Available commands:
 ? | h    - show help                 n [part] - set mount point
 A        - auto partition all space  p [unit] - print partitions
 a [part] - add partition             q        - quit & save changes
 b        - set OpenBSD boundaries    R [part] - resize auto allocated partition
 c [part] - change partition size     r        - display free space
 D        - reset label to default    s [path] - save label to file
 d [part] - delete partition          U        - undo all changes
 e        - edit drive parameters     u        - undo last change
 g [d|u]  - [d]isk or [u]ser geometry w        - write label to disk
 i        - modify disklabel UID      X        - toggle expert mode
 l [unit] - print disk label header   x        - exit & lose changes
 M        - disklabel(8) man page     z        - delete all partitions
 m [part] - modify partition

Suffixes can be used to indicate units other than sectors:
 'b' (bytes), 'k' (kilobytes), 'm' (megabytes), 'g' (gigabytes) 't' (terabytes)
 'c' (cylinders), '%' (% of total disk), '&' (% of free space).
Values in non-sector units are truncated to the nearest cylinder boundary.
> w
> q
No label changes.
/dev/rsd0a: 7067.3MB in 14473856 sectors of 512 bytes
35 cylinder groups of 202.47MB, 12958 blocks, 25984 inodes each
Available disks are: sd1.
Which disk do you wish to initialize? (or 'done') [done] 
/dev/sd0a (0f62129f7e341b8c.a) on /mnt type ffs (rw, asynchronous, local)

Let's install the sets!
Location of sets? (disk http nfs or 'done') [http] 
HTTP proxy URL? (e.g. 'http://proxy:8080', or 'none') [none]
HTTP Server? (hostname, list#, 'done' or '?') [mirror.internode.on.net] 
Server directory? [pub/OpenBSD/snapshots/armv7] 

Select sets by entering a set name, a file name pattern or 'all'. De-select
sets by prepending a '-' to the set name, file name pattern or 'all'. Selected
sets are labelled '[X]'.
    [X] bsd.OMAP            [X] base57.tgz          [ ] xbase57.tgz
    [X] bsd.rd.OMAP         [X] comp57.tgz          [ ] xshare57.tgz
    [X] bsd.OMAP.umg        [X] man57.tgz           [ ] xfont57.tgz
    [X] bsd.rd.OMAP.umg     [X] game57.tgz          [ ] xserv57.tgz
Set name(s)? (or 'abort' or 'done') [done] 
Get/Verify SHA256.sig   100% |**************************|  2500       00:00    
Signature Verified
Get/Verify bsd.OMAP     100% |**************************|  3200 KB    00:08    
Get/Verify bsd.rd.OMAP  100% |**************************|  6577 KB    00:11    
Get/Verify bsd.OMAP.umg 100% |**************************|  3652 KB    00:06    
Get/Verify bsd.rd.OMAP.umg 100% |***********************|  6995 KB    00:11    
Get/Verify base57.tgz   100% |**************************| 49397 KB    01:24    
Get/Verify comp57.tgz   100% |**************************| 43817 KB    01:15    
Get/Verify man57.tgz    100% |**************************|  8764 KB    00:15    
Get/Verify game57.tgz   100% |**************************|  2616 KB    00:04    
Installing bsd.OMAP     100% |**************************|  3200 KB    00:06    
Installing bsd.rd.OMAP  100% |**************************|  6577 KB    00:13    
Installing bsd.OMAP.umg 100% |**************************|  3652 KB    00:07    
Installing bsd.rd.OMAP.umg 100% |***********************|  6995 KB    00:15    
Installing base57.tgz   100% |**************************| 49397 KB    04:43    
Extracting etc.tgz      100% |**************************|   110 KB    00:00    
Installing comp57.tgz   100% |**************************| 43817 KB    03:58    
Installing man57.tgz    100% |**************************|  8764 KB    00:58    
Installing game57.tgz   100% |**************************|  2616 KB    00:13    
Location of sets? (disk http nfs or 'done') [done] 
Time appears wrong.  Set to 'Sun Jan 25 15:29:03 JST 2015'? [yes] 
Saving configuration files...done.
Making all device nodes...done.

CONGRATULATIONS! Your OpenBSD install has been successfully completed!
To boot the new system, enter 'reboot' at the command prompt.
When you login to your new system the first time, please read your mail
using the 'mail' command.

# reboot
syncing disks... done
rebooting...

U-Boot SPL 2014.04-00015-gb4422bd (Apr 22 2014 - 13:24:29)
reading args
spl_load_image_fat_os: error reading image args, err - -1
reading u-boot.img
reading u-boot.img

U-Boot 2014.04-00015-gb4422bd (Apr 22 2014 - 13:24:29)

I2C:   ready
DRAM:  512 MiB
NAND:  0 MiB
MMC:   OMAP SD/MMC: 0, OMAP SD/MMC: 1
*** Warning - readenv() failed, using default environment

Net:   <ethaddr> not set. Validating first E-fuse MAC
cpsw, usb_ether
Hit any key to stop autoboot:  0 
gpio: pin 53 (gpio 53) value is 1
mmc0 is current device
gpio: pin 54 (gpio 54) value is 1
SD/MMC found on device 0
reading uEnv.txt
158 bytes read in 4 ms (38.1 KiB/s)
gpio: pin 55 (gpio 55) value is 1
Loaded environment from uEnv.txt
Importing environment from mmc ...
Checking if uenvcmd is set ...
gpio: pin 56 (gpio 56) value is 1
Running uenvcmd ...
reading bsd.umg
3740120 bytes read in 206 ms (17.3 MiB/s)
## Booting kernel from Legacy Image at 82800000 ...
   Image Name:   boot
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    3740056 Bytes = 3.6 MiB
   Load Address: 80300000
   Entry Point:  80300000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK

Starting kernel ...

OpenBSD/omap booting ...
arg0 0x0 arg1 0xe05 arg2 0x80000100
atag core flags 0 pagesize 0 rootdev 0
atag cmdline [sd0i:/bsd.umg]
atag mem start 0x80000000 size 0x20000000
bootfile: sd0i:/bsd.umg
bootargs: 
memory size derived from u-boot
bootconf.mem[0].address = 80000000 pages 131072/0x20000000
Allocating page tables
freestart = 0x80692000, free_pages = 129390 (0x0001f96e)
IRQ stack: p0x806c0000 v0xc06c0000
ABT stack: p0x806c1000 v0xc06c1000
UND stack: p0x806c2000 v0xc06c2000
SVC stack: p0x806c3000 v0xc06c3000
Creating L1 page table at 0x80694000
Mapping kernel
Constructing L2 page tables
undefined page pmap [ using 299260 bytes of bsd ELF symbol table ]
board type: beaglebone
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.
Copyright (c) 1995-2015 OpenBSD. All rights reserved.  http://www.OpenBSD.org

OpenBSD 5.7-beta (GENERIC-OMAP) #7: Wed Jan 21 05:43:17 AEDT 2015
    jsg@armv7.jsg.id.au:/usr/src/sys/arch/armv7/compile/GENERIC-OMAP
real mem  = 536870912 (512MB)
avail mem = 518791168 (494MB)
warning: no entropy supplied by boot loader
mainbus0 at root
cpu0 at mainbus0: ARM Cortex A8 R3 rev 2 (ARMv7 core)
cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled
cpu0: 32KB(64b/l,4way) I-cache, 32KB(64b/l,4way) wr-back D-cache
omap0 at mainbus0: BeagleBone
prcm0 at omap0 rev 0.2
sitaracm0 at omap0: control module, rev 1.0
intc0 at omap0 rev 5.0
edma0 at omap0 rev 0.0
dmtimer0 at omap0 rev 3.1
dmtimer1 at omap0 rev 3.1
omdog0 at omap0 rev 0.1
omgpio0 at omap0: rev 0.1
gpio0 at omgpio0: 32 pins
omgpio1 at omap0: rev 0.1
gpio1 at omgpio1: 32 pins
omgpio2 at omap0: rev 0.1
gpio2 at omgpio2: 32 pins
omgpio3 at omap0: rev 0.1
gpio3 at omgpio3: 32 pins
omap0: device tiiic unit 0 not configured
omap0: device tiiic unit 1 not configured
omap0: device tiiic unit 2 not configured
ommmc0 at omap0
sdmmc0 at ommmc0
ommmc1 at omap0
sdmmc1 at ommmc1
com0 at omap0: ti16750, 64 byte fifo
com0: console
cpsw0 at omap0: version 1.12 (0), address d0:5f:b8:f5:94:f9
ukphy0 at cpsw0 phy 0: Generic IEEE 802.3u media interface, rev. 1: OUI 0x0001f0, model 0x000f
scsibus0 at sdmmc0: 2 targets, initiator 0
sd0 at scsibus0 targ 1 lun 0: <SD/MMC, Drive #01, > SCSI2 0/direct fixed
sd0: 7580MB, 512 bytes/sector, 15523840 sectors
scsibus1 at sdmmc1: 2 targets, initiator 0
sd1 at scsibus1 targ 1 lun 0: <SD/MMC, Drive #01, > SCSI2 0/direct fixed
sd1: 3688MB, 512 bytes/sector, 7553024 sectors
vscsi0 at root
scsibus2 at vscsi0: 256 targets
softraid0 at root
scsibus3 at softraid0: 256 targets
boot device: sd0
root on sd0a (0f62129f7e341b8c.a) swap on sd0b dump on sd0b
WARNING: CHECK AND RESET THE DATE!
Automatic boot in progress: starting file system checks.
/dev/sd0a (0f62129f7e341b8c.a): file system is clean; not checking
setting tty flags
pf enabled
starting network
DHCPDISCOVER on cpsw0 - interval 3
DHCPOFFER from xx.xx.xx.xx (00:17:e0:a1:61:84)
DHCPREQUEST on cpsw0 to 255.255.255.255
DHCPACK from xx.xx.xx.xx (00:17:e0:a1:61:84)
bound to xx.xx.xx.xx -- renewal in 43199 seconds.
IPv6 autoconf: cpsw0
openssl: generating isakmpd/iked RSA key... done.
ssh-keygen: generating new host keys: RSA1 RSA DSA ECDSA ED25519 
starting early daemons: syslogd pflogd.
starting RPC daemons:.
savecore: no core dump
checking quotas: done.
clearing /tmp
kern.securelevel: 0 -> 1
creating runtime link editor directory cache.
preserving editor files.
starting network daemons: sshd smtpd sndiod.
Path to firmware: http://firmware.openbsd.org/firmware/5.7/
No devices found which need firmware files to be downloaded.
starting local daemons: cron.
Sun Jan 25 15:34:26 JST 2015

OpenBSD/armv7 (foo.tknd.jp) (console)

login: 

3. buildin Debian GNU/Linux OSのboot時log

こちらも比較用として、一応載せておきます。

U-Boot SPL 2014.04-00015-gb4422bd (Apr 22 2014 - 13:24:29)
reading args
spl_load_image_fat_os: error reading image args, err - -1
reading u-boot.img
reading u-boot.img

U-Boot 2014.04-00015-gb4422bd (Apr 22 2014 - 13:24:29)

I2C:   ready
DRAM:  512 MiB
NAND:  0 MiB
MMC:   OMAP SD/MMC: 0, OMAP SD/MMC: 1
*** Warning - readenv() failed, using default environment

Net:   <ethaddr> not set. Validating first E-fuse MAC
Could not get PHY for cpsw: addr 0
cpsw, usb_ether
Hit any key to stop autoboot:  0 
gpio: pin 53 (gpio 53) value is 1
Card did not respond to voltage select!
mmc0(part 0) is current device
Card did not respond to voltage select!
gpio: pin 56 (gpio 56) value is 0
gpio: pin 55 (gpio 55) value is 0
gpio: pin 54 (gpio 54) value is 0
mmc1(part 0) is current device
gpio: pin 54 (gpio 54) value is 1
SD/MMC found on device 1
reading uEnv.txt
1430 bytes read in 5 ms (279.3 KiB/s)
gpio: pin 55 (gpio 55) value is 1
Loaded environment from uEnv.txt
Importing environment from mmc ...
Checking if uenvcmd is set ...
gpio: pin 56 (gpio 56) value is 1
Running uenvcmd ...
reading zImage
3717760 bytes read in 206 ms (17.2 MiB/s)
reading initrd.img
2870014 bytes read in 161 ms (17 MiB/s)
reading /dtbs/am335x-boneblack.dtb
25080 bytes read in 9 ms (2.7 MiB/s)
Kernel image @ 0x82000000 [ 0x000000 - 0x38ba80 ]
## Flattened Device Tree blob at 88000000
   Booting using the fdt blob at 0x88000000
   Using Device Tree in place at 88000000, end 880091f7

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[    0.381743] omap2_mbox_probe: platform not supported
[    0.548644] tps65217-bl tps65217-bl: no platform data provided
[    0.612665] bone-capemgr bone_capemgr.9: slot #0: No cape found
[    0.649771] bone-capemgr bone_capemgr.9: slot #1: No cape found
[    0.686880] bone-capemgr bone_capemgr.9: slot #2: No cape found
[    0.723989] bone-capemgr bone_capemgr.9: slot #3: No cape found
[    0.740142] bone-capemgr bone_capemgr.9: slot #6: BB-BONELT-HDMIN conflict P8.45 (#5:BB-BONELT-HDMI)
[    0.749748] bone-capemgr bone_capemgr.9: slot #6: Failed verification
[    0.756501] bone-capemgr bone_capemgr.9: loader: failed to load slot-6 BB-BONELT-HDMIN:00A0 (prio 2)
[    0.773007] omap_hsmmc mmc.5: of_parse_phandle_with_args of 'reset' failed
[    0.835589] pinctrl-single 44e10800.pinmux: pin 44e10854 already requested by 44e10800.pinmux; cannot claim for gpio-leds.8
[    0.847304] pinctrl-single 44e10800.pinmux: pin-21 (gpio-leds.8) status -22
[    0.854594] pinctrl-single 44e10800.pinmux: could not request pin 21 on device pinctrl-single
Loading, please wait...
Scanning for Btrfs filesystems
systemd-fsck[203]: rootfs: clean, 86458/230144 files, 569092/919296 blocks

Debian GNU/Linux 7 beaglebone ttyO0

default username:password is [debian:temppwd]

Support/FAQ: http://elinux.org/Beagleboard:BeagleBoneBlack_Debian

The IP Address for usb0 is: 192.168.7.2
beaglebone login: [   23.146367] libphy: PHY 4a101000.mdio:00 not found
[   23.151415] net eth0: phy 4a101000.mdio:00 not found on slave 0
[   23.157620] libphy: PHY 4a101000.mdio:01 not found
[   23.162630] net eth0: phy 4a101000.mdio:01 not found on slave 1

Debian GNU/Linux 7 beaglebone ttyO0

default username:password is [debian:temppwd]

Support/FAQ: http://elinux.org/Beagleboard:BeagleBoneBlack_Debian

The IP Address for usb0 is: 192.168.7.2
beaglebone login: root
Last login: Wed Apr 23 20:20:20 UTC 2014 on ttyO0
Linux beaglebone 3.8.13-bone47 #1 SMP Fri Apr 11 01:36:09 UTC 2014 armv7l

The programs included with the Debian GNU/Linux system are free software;
the exact distribution terms for each program are described in the
individual files in /usr/share/doc/*/copyright.

Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent
permitted by applicable law.
root@beaglebone:~# ifconfig -a
eth0      Link encap:Ethernet  HWaddr d0:5f:b8:f5:94:f9  
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
          Interrupt:40 

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:65536  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

usb0      Link encap:Ethernet  HWaddr 76:78:7c:0d:b0:d4  
          inet addr:192.168.7.2  Bcast:192.168.7.3  Mask:255.255.255.252
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

root@beaglebone:~# 

Updated by Tsutomu KIMURA over 9 years ago · 7 revisions locked